SHEAN (CANGZHOU) CORP LTD
Customer first, Quality First, Service first
Add to Cart
Metal Cutting Horizontal Electric Control Band Saw Machine
1. During the operation of the machine tool, it is strictly prohibited to wear gloves; it is strictly prohibited to touch the rotating part of the machine tool by hand, and it is strictly prohibited to transfer objects through the lathe during the operation of the lathe. Loading and unloading of workpieces, installation of cutting tools, oiling and cleaning of chips, must be stopped, power failure. It is forbidden to use the brush or hook to clean the iron scraps by hand, or use the clutch to stop for appeal operation. A kind of
2. When the machine tool is running, it is not allowed to measure the workpiece and directly stop the rotating chuck by hand; when using the abrasive cloth, it should be placed on the file or special board. It is not allowed to wear gloves and use the abrasive cloth. The worn abrasive cloth is not allowed to be used. It is not allowed to use the forward and reverse car electric brake. It must pass through the middle brake. When it is necessary to measure the dimension in rotation due to work requirements,
After the power is cut off, the chuck can be moved by hand to measure (dial indicator, planner, infrared, etc.). A kind of
3. According to the technical requirements of the machine tool, the cutting parameters of the workpiece are selected to cause accidents due to the overload of the machine tool. A kind of
4. During the cutting process, the tool should be completely withdrawn when the machine is stopped. The center frame must be used to cut the long axis to prevent the bending and deformation of the workpiece from hurting people; the length of the bar stretched into the head of the bed shall not exceed the length of the main axis of the head of the bed, and it shall be processed slowly, and the protection shall be paid attention to when extending. When using the center frame, the fixed position shall be reasonable, and it must be clamped under the condition of strict concentricity. It is forbidden to rigidly rotate the three claws of the center frame to clamp the workpiece after correction. A kind of
5. During high-speed cutting, there should be a protective cover, and the fixing of workpieces and tools should be firm. When the spatter of iron scraps is serious, a baffle should be installed around the machine tool to isolate it from the operation area. A kind of
6. When the machine tool is running, the operator shall not leave the machine tool. If the machine tool is found to have abnormal noise, temperature rise, vibration and odor, the operator shall stop the machine immediately and report to the team leader on duty to arrange the maintenance personnel for inspection and repair. When the power is cut off suddenly, the tool shall be quickly withdrawn from the working position and the machine tool shall be shut down at the same time. A kind of
1. Before the machine tool starts to work, preheating shall be in place to ensure the normal operation of the lubricating system (sufficient lubricating oil and coolant). If the machine tool is not started for a long time, the lubricating oil shall be supplied to each part manually
2. When the taper handle is installed in the taper hole of the main shaft and tailstock, the inner and outer cones shall be wiped dry Clean, prevent iron scraps and dust from squeezing into the damaged cone, and affect the accuracy; the cutter used shall be consistent with the specification allowed by the machine tool, and the severely damaged cutter shall be replaced in time. 3. Repair all boxes of the machine tool, and do not forget the tools used to adjust the tools inside the machine tool. A kind of
4. The center hole of large shaft parts must be strictly in accordance with the requirements of the designer. If the center hole cannot be used for large column barrel parts, the center top support of special towing plate must be made. If the center hole is too small, it is easy to be dangerous in work. A kind of
5. The workpiece clamped by chuck must be correct and reliable. When processing parts with large eccentricity, counterweight must be used and installed firmly and reliably. A kind of
6. When loading and unloading the chuck and heavy workpieces, the guide rail shall be padded with wood or rubber, and special personnel shall be assigned to assist the lifting and handling. It is strictly prohibited to operate by single person. After using the chuck wrench, socket, measuring tool, etc., they shall be taken and placed at the safe place such as the headbox cover. III. safety regulations during work
| Type | GZ 4250 |
| Cut capacity W*H (mm) | round 500 |
| square 500*500 | |
| Bundle cutting W*H (mm) | / |
| / | |
| Saw belt size(mm) | 5370*41*1.1 |
| belt line speed(m/min) | 40/60/80 (frequency control available) |
| Main generator power(kw) | 5.5 |
| Hydraulic generator power(kw) | 1.5 |
| Cooling generator power (kw) | 0.09 |
| Working clamp style | Hydraulic |
| Saw belt tighten style | Hand |
| Main transmit structure | Turbine |
| Loading style | Extra roller |
| Packing dimensions(mm) L*M*H | 2800*1300*1800 |
| Weights of machine (kgs) | 2800 |
